Flame- Proof Projecting Lamp
Brand ZM
Certification
Lead Time 15days
Guarantee Period 12months
Source of Supply Guangdong
Payment Method T/T L/C
1. Housing of the projecting lamp is fabricated with die-casting aluminum alloy. Tensile strength of casting aluminum alloy is not less than 120Mpa, and its magnesium content is not more than 0.5% (mass ratio). Plane flameproof structure (Grade ⅡB) is adopted between the housing and the cover. 2. Glass cover of the projecting lamp is fabricated with tempered glass and can withstand 4J impact test. There is a protective screening outside the glass cover. 3. Connection terminal and inner foundation bolt are set inside the projecting lamp. There is a cable entry device on the housing, and cable wiring mode is applied. 4. The projecting lamp can be rotated by ±180° in horizontal direction, and the angle of elevation is adjustable within +90°~-60°. 5. The reflector is of parabolic type, featured by high reflectivity and light equalization of the illuminated surface. 6. Insulating strength of the projecting lamp can withstand AC 2000V power-frequency voltage-withstand test with duration of 1min. 7. Insulation resistance of the projecting lamp is not lower than 1.5MΩ in normal environment. 8. The projecting lamp is featured by high efficiency, long service life, good lighting effect and large illumination area. as the fourth generation light source, LED has good performance with advanced technology, and it has the following advantages: a. Low energy consumption: it is 90% compared with incandescent lamp; b. Long service life: it can reach 30,000-50,000h at proper current and voltage, tens times of that of lamps of the same kind; c. High luminance, high color rendering index (Ra> 80), and good directionality of light source; d. Environmental protection: the light source is fabricated with nontoxic semiconductor material that is pollution-free; e. No thermal radiation: it is applicable for environment with strict explosion-proof requirements. BT 51 series flame-proof projecting lamp (hereinafter referred to as the projecting lamp) is designed and manufactured as per the standards in Explosive Atmospheres (GB3836.1~3-2010). It is used in zone 1 and zone 2 in T1~T3 places with explosive gas mixture of Category Ⅱ Class A/B indoors and outdoors, and it is used for lighting in line of AC 50HZ/60HZ with rated voltage of 110V and 220V. Explosion-proof performance of LED BTb51 explosion-proof projecting lamp (hereinafter referred to as the projecting lamp) complies with the regulations of Explosive Atmospheres - Part 1: Equipment - General Requirements (GB3836.1-2010) and Explosive Atmospheres - Part 2: Equipment Protection by Flameproof Enclosures "d" (GB3836.2-2010). It is used in zone 1 and zone 2 in T1~T4 places with explosive gas mixture of Category Ⅱ Class A/B indoors and outdoors, and it is used for lighting in line of AC 50HZ with rated voltage of 220V.
Technical Parameters:
1. Power: 400W, 100W LED; 2. Voltage: 110/220V; 3. Explosion-proof mark: ExdⅡBT3 Gb, ExdⅡBT4 Gb; 4. IP grade: IP54, IP66
Recommendations
28pcs. Thread Taps Set
BrandENDURA
(Carbon Steel) No Leakage WaferCheck Valve
BrandCD
25-225THC Tubing Pump
BrandFUQIAO
KS021552-Safety Shoes
BrandKANGSHIELD
Hoisting Tools | BJ Type 350ton Elevator/Spider 4-1/2"~13-3/8" |SEB350
BrandRUTONG
4"NPS Butt Welded Straight Cross
BrandRUNYANG
3/8" Dr. 6pt Deep Socket
BrandENDURA
Oil Seal of Input Shaft, 55x80x10 | Agitator HA-5.5/HA-7.5/HA7.5-2
BrandTSC
Suction Pump Accessories-Fixed Valve Cover
BrandBAOSHI
Half-Round File 10"
BrandENDURA
Upper/ Lower Impeller Assembly, P/N: HNJ7.5-04, HNJ7.5-07-2 | Agitator HA-7.5/HA7.5-2
BrandTSC
KS021546-Safety Shoes
BrandKANGSHIELD
Spinner Handle
BrandENDURA
Urethane Bonded Pistons|Sizes in Millimeters|With Piston Bore 38.1mm
BrandKERUI
1/2" Dr. Bit Sockets Hex
BrandENDURA
20-175RHBM Rod Pump
BrandFUQIAO
Rotating Shaft Assembly, P/N: HNJ7.5-03 | Agitator HA-7.5/HA7.5-2
BrandTSC
Screwdriver Phillips
BrandENDURA